The microwave works, but does not heat - reasons for how to repair it yourself

The microwave does not spin - any owner can face this problem. We have collected all diagnostic and repair options in the article.

Microwave ovens of the new generation are a real “first aid” in the kitchen. It takes just minutes to cook, heat and defrost. The microwave oven comes with a special rotating plate - a tray on which food or ready-made dishes are placed. Rotation is necessary for uniform heating: the food is turned with all sides towards the microwave source - the magnetron.

How does a microwave oven work?

To repair/maintain any equipment, including a microwave oven, you need to know the principle of its operation. Let's look at the basic elements and their purpose.

Magnetron

At the heart of a microwave oven is a magnetron, which, when turned on, produces microwave energy and distributes it throughout the interior.

The magnetron screen is located inside the microwave on the right behind the wall where the control panel is located. It is made in the form of a cover, which is attached to latches or screws.

The function of the screen is to protect the magnetron from particles of food from the cooking zone.

The device is connected to the camera using a rectangular waveguide, which is covered with a glass or plastic cover.

Power supply

Transformers-stabilizers, which are the most complex and expensive element, act as a power source.

As additional equipment, a multiplier is used, which includes a capacitance and a diode bridge.

After applying voltage to the magnetron, the fan also turns on, which distributes warm air and thereby speeds up the cooking process.

Frame

The microwave has a rectangular body, which is key when heating.

The heat and waves generated during operation are reflected from surfaces and distributed evenly inside.

An additional advantage is the rotation of the saucer on which the food is placed. This function is provided by a special motor.

Control Panel

The microwave oven is configured using the control panel.

Depending on the complexity of the equipment, it can be mechanical (rotating handles) or touch (buttons).

Additionally, a number of protections are provided to ensure safe operation.

For example, when the door is opened, the oven automatically stops working. There is also a timer that turns off after a certain time.

Door

When making a microwave oven, special attention is paid to the door. The gap between it and the body should be minimal.

An HF choke valve is installed along the perimeter, acting as a barrier to dangerous waves.

In addition, plastic that can absorb radiation is used in manufacturing.

About security

Contrary to popular belief, a microwave does not emit radioactive waves, so when heated, at least 75% of the nutrients in food are retained.

Electrical diagram

Microwave ovens use different electrical circuits, but the general layout is the same. Electronics parts can be divided into control and executive. The first includes the following elements:

• microcontroller;
• control Panel;
• display;
• electromagnetic relays;
• buzzers.

When they are combined, a kind of “brain” of the microwave oven is obtained - the power and control board. A small step-down transformer is used to supply power to the control part. The microcontroller uses transistors to control three electromagnetic relays. Turning them on and off directly controls the operating algorithm of the device.

The magnetron of a microwave oven belongs to the executive part. It also includes a glass stand motor, a cooling fan, a backlight and other elements. One of the most important participants in the circuit is the high-voltage transformer. This is the largest element of a microwave oven, which is capable of receiving a power of 1.5–2 thousand watts. Of these, about 500−850 are the useful part. The magnetron consists of the following parts:

• antenna;
• braid;
• chassis;
• radiator;
• connector

An alternating current with a voltage of 220 volts is supplied to the primary winding of the transformer, and an outgoing voltage of 3.15 volts is supplied to the filament winding of the magnetron. Because of this, electrons are emitted. The current consumed can reach ten amperes.

There is also a secondary winding. Together with a voltage doubling circuit involving a high-voltage capacitor and diode, it produces a current of 4 kW, which powers the magnetron. Its power is small - approximately 0.3 A.

The electrons produced by the filament winding begin to move in a vacuum along a special trajectory. This creates microwave radiation, which comes from the magnetron into the chamber through an antenna and a rectangular waveguide. The camera itself in this simple circuit plays the role of a resonator. Ultra-high frequency waves are reflected many times from the walls, again passing through the food.

In part, the control elements can be called protective mechanisms. For example, thermal switches prevent possible overheating. Normal operating temperature is from 80 to 100 degrees. One of the thermal switches is installed on the magnetron. Two more control the temperature of the air duct and grill.

If one of the sensors detects a critical value, the thermal switch opens the circuit. Electricity stops flowing to the magnetron. This usually happens at 120-145 degrees - this temperature is still safe.

Three switches are built into the right end of the microwave chamber, opposite which the door is located. The main and secondary contacts close when the furnace is closed, and the control contact opens. If at least one switch fails, the fuse will trip and the device will not turn on.

To reduce interference occurring in the electrical network, there is a surge filter.

Reasons why the microwave does not heat, but works

Experts identify many reasons why a microwave may work, but not perform basic heating functions. Conventionally, all reasons are divided into the most common, simple and complex.

To avoid confusion, we will consider them separately.

Common faults

First, let's highlight the most common explanations for the fact that the microwave oven does not perform its functions:

1. Heating food with metal elements: spoon, fork, etc.
2. Using unsuitable utensils: metal, gold-rimmed, lidded, etc.
3. Low quality equipment and rapid failure. Many manufacturers do not bother with high quality parts so that customers go for new products.
4. Natural aging of microwave elements, etc.

Simple causes and tips for eliminating them

There are many simple faults that cause a microwave oven to malfunction.

Let's highlight the main ones:

If the options considered are checked, but the device still does not work, there is a serious malfunction.

In this case, it is necessary to conduct additional diagnostics.

Complex malfunctions, the microwave heats up but makes a humming sound

In more complex cases, we are talking about some kind of equipment malfunction. After turning on, the tray rotates, the light is on, but the microwave oven does not heat anything. There may be several reasons for this.

Control block

To determine whether the control unit is faulty, it is important to have some experience. In the absence of one, it is better not to meddle with this mechanism due to the risk of damaging expensive elements.

For beginners, the best way is to replace the equipment or update its firmware.

Magnetron

The most difficult situation is when the microwave does not work due to damage to the magnetron.

The malfunction of this part may be due to the following reasons:

1. Poor contact connection. If the contact weakens, heating occurs at the connection point, which leads to the impossibility of normal operation. To fix the problem, you need to compress the contact group using pliers.
2. Deterioration of the metal. Many microwave ovens have a hole in the cap through which you can look at the metal elements and evaluate their condition. If the metal is intact, the problem is in the cap, which requires replacement. If the metal is damaged, the microwave may break. The solution to the problem is to replace the magnetron, which is expensive, or to buy a new microwave oven.
3. Traces of burnt or metal drops on the surface. To remove them, use sandpaper to clean the cap and thus improve its conductivity.

Fuse

In a situation where the microwave does not work, check the integrity of any fuses that may have blown. Externally, such elements look like a glass flask with metal inserts inside.

There are caps installed on the sides, to which a wire in the form of a spring is connected.

The current passes through the fuse and if this parameter exceeds the optimal norm, the insert burns out.

There is also a situation when the wire simply comes off, which is why the voltage does not flow into the microwave oven.

Mica plate (magnetron screen)

A special plate is installed inside the heating zone, which can be inspected visually and identify a malfunction.

With prolonged use and lack of proper care, soot may appear on this element and a thick layer of fat may accumulate. This dirt interferes with the normal operation of the element and causes the microwave oven to not work.

In addition, contamination may cause sparking or cracking noises. In the most difficult cases, the part may even catch fire.

Capacitor, transformer

If the microwave oven does not heat food and makes a lot of noise, in 90% of cases the cause is a burnt-out capacitor.

If smoke appears after turning on the device, this indicates damage to the transformer.

A malfunction can be indicated by normal overheating without damage to the part.

Diode

A broken diode can lead to heating and damage to the capacitor.

Diagnosing such a malfunction is a complex process, so replacement is carried out even if a breakdown is suspected.

Inverter

The purpose of the device is to determine the temperature inside the chamber and the products themselves.

Control is carried out using sensors that can fail or provide incorrect information.

In both cases, the microwave oven simply will not heat the food.

Timer

If damaged, the timer does not work correctly and begins to randomly turn on and off the equipment.

It makes no sense to repair this part, so the only correct solution is replacement.

Device principle

A capacitor is a device that has the ability to store a certain charge of electricity. It consists of two metal plates installed in parallel, between which there is a dielectric. Increasing the plate area increases the accumulated charge in the device.

There are 2 types of capacitors: polar and non-polar. All polar devices are electrolytic. Their capacity is from 0.1 ÷ 100000 µF.

When checking a polar device, it is important to observe the polarity, when the positive terminal is connected to the positive terminal, and the negative terminal to the negative terminal.

It is polar capacitors that are high-voltage, while non-polar capacitors have low capacitance.

Microwave showing the location of the capacitor

The power supply circuit of the microwave magnetron includes a diode, transformer, and capacitor. Through them up to 2, 3 kilovolts goes to the cathode.

The capacitor is a large part weighing up to 100 grams. A diode lead is connected to it, the second one on the body. A cylinder is also located near the block. This particular cylinder is a high voltage fuse. It should not allow the magnetron to overheat.

Diagnostics and troubleshooting

Before carrying out repair work, it is important to carry out diagnostics to determine the malfunction.

In a situation where the microwave does not work, turns on every once in a while, hums or does not heat, but works, do the following:

1. Check the voltage supplied to the transformer. To do this, use a regular multimeter and follow safety precautions. If the voltage drops below 215 Volts, connect a stabilizer or wait until this parameter normalizes.
2. Check that the door latch is working properly.
3. Make sure that the contact connections are reliable, as well as the serviceability of the main elements.
4. Disconnect the microwave oven from the power supply and remove the upper part of the housing.
5. Remove the chip from the magnetron and check it.
6. Place the magnetron terminals in place.
7. Check the capacitor.
8. Check diodes.
9. Check the integrity of the fuses. Burnt-out elements are immediately visible by blackening.
10. If the latter burns out, check the multiplier nodes.

We will consider the features of checking each of the above elements in a separate section below.

After identifying the malfunction, you can decide whether to repair the microwave oven.

If there is a crackling sound, do the following:

1. Determine which part the cracking is coming from.
2. Turn off the power.
3. Remove the mica plate and replace it (costs about two dollars) if it is burnt.
4. Unscrew the magnetron, which is attached to 2-4 screws.
5. Remove the cap that is located at the outlet. If it is tight, loosen it and remove it by hand.
6. Look at the metal outlet under the cap to see if there is a breakdown. If such traces are present, the magnetron must be replaced.
7. If the feed-through capacitors fail, they must be replaced.
8. If the cap is burnt out, replace it.
9. Replace the capacitor if it is the one that fails.

Destruction of the cap on the magnetron

There are frequent cases of breakdowns associated with the destruction of the cap on the magnetron. The thin aluminum case simply cannot withstand the loads and is destroyed by microwave waves. This problem often occurs in older devices that are more than several years old. Obvious symptoms in this case are noise and sparks during operation of the device.

To check, it is enough to remove the transformer, because the cap is located towards the food chamber. If the cap is destroyed, then there are 2 options:

• Replacing the cap.
• Flipping the cap.

The first option is a priority; it is enough to order a replacement or send the magnetron for repair. The second option is considered a temporary alternative that allows you to extend the life of the device indefinitely. It is enough just to rotate the cap 180 degrees around the axis, because the load falls on only one half.

Repair rules

Unqualified repairs often lead to negative consequences in the form of health problems or worsening microwave malfunctions.

To eliminate such moments, follow these rules:

1. Always relieve tension before carrying out repair work. To do this, remove the cord from the outlet.
2. Use protective gloves made of dielectric material that can protect against voltages up to 1000 V.
3. Perform repairs/diagnosis using tools that have insulated handles.
4. Do not apply voltage to the microwave after parts have been removed, without food, with the door open, or if there is a suspected malfunction.
5. Discharge the capacitor before checking, removing or replacing. For this
6. Be careful and check the microwave oven for metal objects inside after repair. ATTENTION: It is normal for a spark to jump between the housing and the capacitor.
7. Do not drill holes in the case, as this may damage the device.

Preparatory stage

Before starting repairs, it is necessary to collect as much information as possible about the failed device. Ideally, this is a service manual for a specific model. In this document, the manufacturer provides all the necessary data, starting from the assembly drawing (exploded view, literally from English explosion diagram) and ending with a troubleshooting algorithm.

Fragment of the explosion diagram of a microwave oven

Unfortunately, manufacturers are in no hurry to share this information, distributing it only among networks of certified service centers. If you manage to find technical documentation for repairs, be prepared for the fact that it will be in English.

If the documentation could not be found, and this will happen in most cases, do not be discouraged; typical microwave oven malfunctions can be determined without having a circuit diagram. It is enough to know what the main elements look like and where they can be located. A photo of a microwave with the casing removed will help you with this.

Appearance and location of the main elements in the microwave body

The intuitiveness of the process in most cases allows you to remove the casing and get to the main structural elements without an assembly drawing. But in this case, you need to remember the sequence of actions and try not to leave behind “extra” parts after reassembly.

What tools are needed?

In most cases, you can get by with a Phillips screwdriver and a multimeter. In some cases, you may also need a soldering iron. Accordingly, spare parts will also be needed, which ones will become clear after the diagnosis.

Features of repairing models from different manufacturers

Despite the similarity in design and operating principle, each manufacturer uses its own secrets in the manufacture of equipment.

Taking this into account, you need to take an individual approach to repairs and pay attention to the manufacturer’s brand.

Below we will consider the features for each of the options and summarize them in a table.

How much does the repair cost?

If you lack experience, it is better to entrust microwave oven repair to specialists. Depending on the policy of the service center and the complexity of the malfunction, the cost of work may vary.

For example, for a simple repair you will have to pay from 1000 rubles, for work of average complexity - from 3000 rubles, and for solving a complex problem - from 6000 rubles. (at the end of 2022).

Common breakdowns:

1. Buttons do not work due to damage to the control panel - from 2600 RUR.
2. Malfunction of the magnetron, capacitor - from 2550 rubles.
3. Replacement of a fuse due to blown during a power surge - from 2600 RUR;
4. Sparking in the device - from 3150 rub.
5. The start button on the microwave oven (control unit) is not pressed - from 2900 RUR.
6. Damage to the heating element - from 3200 rub.
7. Door malfunction - from 2650 RUR.
8. Breakdown of the motor for rotating the plate - from 2550 rubles.
9. The device does not turn off (timer, switch) - from 2650 rub.
10. Microwave oven does not turn on (electrical circuit) - from 2900 rub.

The exact price is determined individually after diagnostics and determination of the malfunction.

Prevention of breakdowns

To protect your microwave oven from damage and extend its service life, you must follow a number of simple rules:

1. Heat food only in the “correct” containers, which are recommended for use in a microwave oven. It is prohibited to use metal containers or utensils with metal, silver or gold plating. Otherwise, there is a high risk of the equipment catching fire.
2. Do not place anything on top of the microwave.
3. Do not cover food containers completely while heating. This is important for steam release.
4. Do not use carriers to connect.
5. Do not drink alcoholic beverages.
6. Do not boil/heat eggs or other foods that are restricted by the microwave manufacturer.
7. Cover food with a special cap to protect the inner surface from grease. This simple rule can significantly extend the service life of the product.
8. Install the microwave oven taking into account the manufacturer's recommendations.
9. Do not turn on the microwave without food inside.
10. When cooking vegetables, make cuts to allow the internal juices to escape.
11. Close the doors carefully to prevent damage to the latch and other parts.
12. Constantly clean the microwave from grease and food debris, especially pay attention to the magnetron screen. Dirt accumulated on it leads to sparking and the appearance of extraneous noise.

If possible, use heat-resistant dishes made from special glass.

Its features include the ability to evenly distribute heat, which allows you to cook food faster and avoid consequences.

It is better to use a transparent and oval container for heating/cooking. Alternatively, you can use porcelain, glass, special plastic or ceramic dishes.