Review of motion sensor IEK DD 009: characteristics and reviews, instructions for connection and configuration

Motion sensor DD 008

This detector is an infrared type for surface mounting. The case with IP44 protection is made of flame retardant plastic (polycarbonate):

• dimensions 87/145/125 mm;
• range of action 8 meters;
• viewing angle 120 degrees;
• recommended installation height 1.8-2.5 m;
• maximum permissible load 1200 W for halogen lamps, 300 VA for fluorescent lamps;
• operation at lighting levels of three lux;
• shutdown delay 10 sec - 7 min;
• operating temperatures -25/+45 degrees Celsius.

Technical characteristics of IEK infrared sensors

Technical parameters are contained in DD 008 operating instructions. The situation is the same with motion alarms DD 009 and DD 010. All data on these devices is listed in the table below.

Specifications table

The models differ in size and design.

Important! The number in the marking indicates the effective viewing range of the device. So, for example, the DD 009 motion sensor has an effective distance from the moving object being detected is 9 meters. DD 008 has 8 meters. The overall figure is 12 meters - this is the maximum response distance of all models of IEC sensors.

Motion sensor DD 009

Just like the previous model, it is a surface-mounted detector with a degree of protection IP44. The differences from DD 008 are only in appearance and a couple of nuances:

• dimensions 87/145/125 mm;
• operating range 8 meters;
• The viewing angle of this device is 100 degrees;
• installation height 1.8-2.5 m;
• maximum permissible load 1200 W/300 VA;
• response threshold from 3 lux to daylight;
• shutdown delay from 10 seconds to 7 minutes;
• temperature range -25/+45 degrees.

The lineup

The most popular models include a number of devices such as DD 0.12, 018V, 017, 019.

DD-012

The alarms perform the function of turning on and off the load when motion is detected in the control zone. The horizontal detection angle is 180 degrees. The sensor is powered from a standard household power supply: 230 V/50 Hz.

The IEC device is enclosed in a three-component housing made of white self-extinguishing plastic. The DD head rotates both horizontally and vertically. The sensor is designed for wall mounting.

To connect the device, wires with a cross section of 0.75 to 1.5 mm are used. The operating range according to the marking is 12 meters.

The operating temperature range is -25 - +450С. Service life – 7 years. The manufacturer guarantees trouble-free operation of the sensor for 5 years.

DD-018V

Power supply from household power supply (230V/50Hz). The effective depth of the control zone is 12 m. The circuit diagram is no different from other IEC sensors. The advantages of the device are as follows:

• The tilt angle is adjusted by a hinge connecting the holder and the DD body;
• Possibility of setting the dwell time - the time before the load is turned on when movement in the control space stops;
• By turning the “Sens” knob you can set the required viewing depth (up to 18 m);
• Convenient hanging in the corner of adjacent walls increases the efficiency of the sensor;
• The tightness of the housing, resistance to UV radiation - these qualities allow the devices to be placed on the walls of the facades of houses to regulate street lighting;
• The horizontal viewing angle is 2700.

DD-017

The sensor is designed for a load power of 300 VA. It is used to service startless fluorescent lamps. The horizontal detection angle is 1200. Protection class against electric shock is II.

The alarm body is made of white plastic with a high degree of fire resistance. The type of power supply is standard, from a household electrical network with a voltage of 230 V. The effective installation height of the device is 1.8-2.5 m. The warranty is 5 years, with a maximum service life of 7 years.

DD-019

The body is made of non-flammable plastic (polycarbonate). The operating time range is from 2 to 7 minutes. Like all sensors, the IEC device switches the load using an electromechanical relay. The alarm is installed both indoors and outdoors.

The sensor head rotates in two planes. The horizontal control angle is 1200. The maximum detection range of a moving object reaches 12 meters. The body color is black.

Motion sensor DD 010

Polycarbonate surface mounted wall sensor for indoor and outdoor use:

Motion sensor DD 010

Review of motion sensor IEK DD 009: characteristics and reviews, instructions for connection and configuration

Reading time: 5 minute(s)

Among the many devices for the home, such a device as the DD 009 motion sensor does not seem very noticeable. But this little device is very important. It helps save electrical energy and time. You don't have to worry about the lights being on. A smart device will do this for you.

What is a motion sensor IEK DD 009?

The IEK DD 009 motion sensor is an infrared sensor. It controls lighting and reacts to moving objects. There is a relay inside that controls turning on the light.

What does it look like and where is it used?

The sensor can be used indoors and outdoors.

The device comes in mostly white or black. Typically, motion sensors are installed in common areas where people walk, but it is not practical to use lights that are always on. These are landings, basements, entrances, courtyards. In an apartment, it is often necessary to install such a sensor in the bathroom, toilet or hallway.

How it works: device and principle of operation

The motion sensor has an infrared sensor that responds to heat waves emitted by an object. The signal is sent to an output device, usually light or sound.

The infrared motion sensor DD-009 has a viewing angle of 180º. The range of this device is 12 meters. The weight of the device is 0.16 kg. The sensor can be installed either on the wall or on the ceiling.

Reviews of motion sensors DD 009: pros and cons

According to user reviews, DD 009 motion sensors have their own positive and negative features.

pros

• Energy saving.
• Convenience. There is no need to worry about the lights not being turned off, and if your hands are busy, the device will do everything for you.
• Affordable price.
• Easy installation.
• Connection to 220 V network.
• Ability to adjust sensitivity and light delay.

Minuses

• If there is no movement, the light turns off, and this is not always convenient.
• The infrared sensor may falsely respond to the heat of a lamp, a nearby heating device, etc. Therefore, you need to choose a place for the device in advance.

Specifications

The device is intended for lighting control. Can be used with multiple bulbs as well as one spotlight.

Has the following technical characteristics:

• adjustable lighting delay (up to 7 minutes);
• the ability to turn on at night or during the day, as desired;
• viewing angle - 180°;
• range - 12 m;
• voltage 220 V;
• relay energy consumption is 1.2 kW, in standby mode it consumes 0.45 W.

Connection and operation instructions

Work on installing and connecting the motion sensor must be carried out with the voltage turned off.

The device comes with instructions that describe in detail the entire connection process.

1. Two wires - phase and zero - supply power to the sensor. The phase comes out of the sensor with one wire and goes to the incandescent lamp.
2. The second end of the lamp is connected to the neutral wire. The relay is shown conditionally to make the operating principle clearer.
3. When movement occurs, the contact closes and the lamp lights up.
4. If there is no movement, the sensor does not operate, the light does not light up or turns off.

There are two types of sensors - wall and ceiling. They have the same principle of operation, but are installed differently.

Depending on the location, the viewing angle changes.

Ceiling models are usually installed in small rooms where the device can cover all four sides. The overview of the protected area is 360°; the sensor is installed at a height of 2.5-3 m from the floor.

The area monitored by the device is 10-20 m. When a person appears in this area, the sensor is triggered.

Wall sensors have a wider range of applications. They can be installed both outdoors and indoors. Just like ceiling ones, they create a multi-beam barrier, when crossed, the electrical circuit is closed and the light comes on.

The installation height is 2-2.5 m, the protected area is 10-15 m.

Connection diagram DD 009

In some cases, it is necessary to leave a regular switch, which will operate in parallel with the sensor. After all, sometimes light may be needed during daylight hours, or it will be needed for a long time. At such moments, it will be easier to turn on the light regardless of the sensor.

Setting up device operation

Before work, you need to configure the sensor. The iek dd 009 infrared motion sensor has two adjustable settings: TIME and LUX. Their adjustment contributes to the correct operation of the device.

1. TIME - time regulator. Sets the lighting delay from the moment it is turned on until the last motion is detected. Depending on the sensor models, this time varies. The dd 009 sensor has a shutdown delay from 10 seconds to 7 minutes.
2. LUX - adjusts the light threshold. In other words, we set the mode so that the light does not turn on during the day. When the illumination is below a preset threshold, the sensor will work and the light will turn on, but during daylight hours, even when moving, the device will not work.

After setting the settings, you can supply 220 V power. Be sure to check the operation of the device. If the light in the room turns on immediately after the object appears, then all settings are made correctly.

Installation Features

When installing the device, you need to take some points into account.

1. When installing, make sure that the sensor is not close to heating devices or windows (sunlight). Any objects that emit light or heat will cause the sensor to respond. The best installation option is in the corner of the room. This will provide greater visibility and coverage area for the rays.
2. If installation is carried out outdoors, do not mount the device close to bushes and trees.
3. Electromagnetic radiation will also cause the device to malfunction.
4. The motion sensor must be located exactly in the place that needs to respond to movements.
5. Dirt and dust can also cause malfunction, so keep the device clean.

Price

The devices are manufactured by IEK. The technical characteristics are the same, so their cost will depend on the manufacturer and the company supplying the devices to the market. Also, the price depends on the city and delivery method.

Prices for the models are almost the same, with a slight deviation and range from 363 to 415 rubles. The device is inexpensive and accessible to almost everyone.

Where to buy motion sensor IEK DD 009?

In Moscow

• , Ilmensky proezd, 1, building 14, 7(495)640-08-04
• , Dorozhnaya st., 60, 7(495)638-57-56
• Online store "Motion Sensors", Volgogradsky Prospekt, 32, building 25,

In St. Petersburg

• , Vitebsky pr-kt, 13, letter A, 8(812)240-05-13
• Online store "Electrics cheap", st. Emelyanova, 12, letter P, office 14,
• Company I SEE YOU, Yesenina str., 11, building 1,

IEK DD 009 motion sensors are installed in places where people are present, where it is impractical to install a regular switch. According to user reviews, this device helps save energy and creates comfort in the room.

Did this article help you? We would be grateful for your rating:

5 4

Motion sensor DD 012

This device, compared to previous ones, has a wider viewing angle, so it can be mounted a little higher to fully reveal this capability:

• dimensions 72/82/122 mm;
• the range of the working area is eight meters;
• viewing angle 160 degrees;
• height recommended for installation is 1.8-2.5 m;
• maximum load power 1200 W/ 300 VA;
• photosensitivity from 3 Lux to daylight;
• operating temperature range -25/+45.

Motion sensor DD 018V

It has absolutely the same characteristics as previous devices, excluding dimensions (77/118/156 mm). It is also worth noting the working area of ​​this model, which is slightly wider than the others. The IR sensor looks at the same 8 meters into the distance, but the viewing angle is as much as 220 degrees, which makes it possible to install it on the outer corners of buildings.

As you can see, IEC clip-on detectors have almost identical characteristics, differing only in the nuances, which can be understood by asking the question: what is the application of the device, the location and purpose of its installation.

Motion sensor DD 035

This device has absolutely the same characteristics as the previous one, being, in fact, a detector of the same type, but a little more technically equipped.

Taras Kalenyuk

auto RU

What's the difference? The DD 035 motion sensor is also capable of capturing sound, while the previous model only reacts to the movement of warm objects.

The described device has several operating modes:

1. included;
2. disabled;
3. Motion Detector;
4. motion detector + sound.

The maximum total load on this device should not exceed 500 W, and the sound volume to which the DD 035 motion sensor can react is represented in the range from 30 to 90 decibels. The previous detector does not have the ability to switch modes while working in one. Accordingly, there is some difference in price.

Motion sensor DD 035

Purpose and principle of operation of the IEK infrared DD

Motion sensors are designed to detect the movement of objects in a protected space and turn on various equipment: alarms, video equipment, lighting, etc.

The device reacts to moving objects in the viewing area. The sensor records the infrared (IR) background of the controlled space. If the IR radiation field is static, the device is in standby mode. If a person appears, the photocell reacts to changes in the level of IR radiation and turns on the relay. It, in turn, closes the power contacts of the security system or turns on the lighting devices.

Motion sensor DD 201

This device, unlike the previous ones, is a built-in ceiling type. If you look closely at its appearance, you can guess that it can be installed in the sockets for spotlights on a suspended ceiling, which is a good reason for using it in such a place.

In terms of incoming load and other characteristics, it is practically no different from previous models. The only thing worth noting is that since this is a ceiling detector, the maximum installation height is higher than that of wall detectors (up to 4 meters). In addition, its viewing angle is 360 degrees.

We recommend to buy

How to connect the sensor?

Depending on the location and purpose of installation, the connection diagram may differ. The parallel method implies separate operation of the device, regardless of the switch. The serial connection type makes it possible to turn off the device using a switch (as well as turn it back on by turning the switch to the “on” state).

Before connecting the sensor, you must carefully study the manual on how to connect the device. Instructions, diagrams, safety precautions are documents that must be carefully read and followed. It is unlikely that the presence of an incorrectly connected system will lead to any consequences, but such a sensor will not work, which will force everything to be disconnected, disassembled and redone.

YouTube responded with an error: The provided API key has an IP address restriction. The originating IP address of the call (87.236.20.136) violates this restriction.